Dojo Decoration System 2.0

decoration system6. The gap shown in FIG. 6 is exaggerated for illustration functions. In normal use, layers 112 and 132 would contact each other within the space of every wire slot 138, however wouldn’t be adhered or hooked up together in the area of each wire slot 138.

Preferably no less than one pin location 244 is disposed near end 213 and another disposed near finish 211. Most preferably there are several pin places/marked spots 244 positioned at varied factors on surface 214 around the perimeter of base 212. Marked spots 244 could also be outlined or colored in another way than the opposite portions of floor 214 or decorative elements 226. Alternatively, ornament equipment may embrace a separate diagram indicating the place on base 212 pin insertion locations 244 are situated without truly requiring any bodily markings on surface 214 or ornamental parts 226. The marked spots 244 indicate an unobstructed or minimally obstructed space 245 and/or 246 as shown on FIG.

If base 12 is a smaller shape, similar to an arc or rectangle, that alone would only partially cover the specified wreath base, a wire 24 (or 124 as proven in FIG. 7A where wire units 25 aren’t used) or a wire set 25 is preferably placed near each of the longitudinal ends eleven and 13 of base 12, with additional wires or wire sets being spaced out from the ends. In this most well-liked embodiment, wires 24a and 24b are ideally completely hooked up to surface 14 using adhesives or by sewing. The wires lengthen laterally throughout base 12 with the ends of the wires 24a and 24b extending sufficiently past the side edges 15, 17 of base 12 to supply sufficient size to wrap the wires across the wreath base and twist them together on the again aspect of the wreath base or other substrate.

Pat. No. 4,133,922 discloses a wreath base having protruding retaining members that type slots into which a stem of a ornament is inserted. The retaining members are spaced out alone the wreath in order that the decorations inserted into one retaining member cover up the following retaining member.

EFI Launches Cubik Digital Inkjet Decoration System For Woo

In another most popular embodiment, wire slots are not used, however the unused wires may still be tucked away from sight within the layer attachment set-back area between the higher and lower base layers close to the perimeter edge. Attachment clips 116 can also optionally be removable from ornament apparatus 110, as they’re proven separately in FIG.

TAKUBO TVJ Inkjet-ornament system video is uploaded.

No. 5,789,043 discloses a ornament base with prongs extending from the base. The prongs are inserted by way of branches on the wreath to carry the ornament base in place. This sort of attachment mechanism can be not useable with a foam or straw kind wreath. The ornament apparatus according to declare 1 wherein the equipment is removably attachable to a couple of sort of substrate and wherein the primary base attachment mechanism is configured to connect the apparatus to no less than one type of substrate and the second base attachment mechanism is configured to attach the apparatus to no less than one other type of substrate.

Alternatively, clips sixteen and wires 24 may be used in conjunction to provide additional safety in the attachment of ornamental equipment 10 to the wreath base. Using each base attachment mechanisms could also be significantly useful if the wreath will be used outside in unprotected windy conditions.

Alternatively, pin location 244 may be a minimally obstructed area the place there isn’t a different attachment mechanism that would obstruct insertion of a pin and the place there’s a minimal amount of glue or stiches between the layers. Most ideally, in a minimally obstructed embodiment, there may be both a pocket 245 or a pocket 246, so that glue or stitching is simply between either the ornamental elements and upper base layer or between the upper and lower base layers, however not each so that a straight pin could also be inserted with out a lot issue. According to a different most well-liked embodiment, base layer 132 may includes a plurality of slots (not proven) via which a portion of ornamental parts 126 may be inserted, corresponding to a stem on a floral factor. Having a portion of an ornamental component 126 between base layers 132 and 112, ideally secured with an adhesive, aids in structural stability and ensuring that ornamental components 126 don’t become dislodged from the base, which can happen if they are only connected to an higher surface 136 of base layer 132. Base 12 is shown with rectangular shape, that would work well to cowl part of a round, oval, square, or rectangular formed wreath base, however would also work to cowl part of another formed wreath (such as a heart or star).

According to another preferred embodiment, the wire is connected to the highest or higher surface of the bottom, between the base and ornamental parts. According to another most popular embodiment, a minimum of one set of wires is used as a base mechanism, with every wire in a set having at least one characteristic (such as colour and/or gauge) different from the opposite wire or wires within the set.

It can be costly for the consumer to purchase so many wreaths, particularly when it ends in duplicates of the type of wreath base. As a substitute for material base layers, plastic, steel or wood may also be used for base 12, 112, 212, 132, and/or 232. These different base materials present greater power and stability, which can be useful for significantly heavy decorative parts.